Roofers in Midvale, UT

Roofing has a low barrier to entry and a long feedback loop — a bad install can look perfect for four years. These are the checks that actually separate companies, in rough order of how much they tell you.

1. 1

   Verify the Utah license, then verify the insurance separately

   Ask for the DOPL license number and look it up yourself. Then ask for a certificate of insurance sent directly from the insurance agent, not a PDF forwarded by the contractor. Both general liability and workers’ compensation. If a worker is hurt on an uninsured crew, the exposure can land on the homeowner.

2. 2

   Require the scope in writing, itemized

   Underlayment type, ice-and-water shield coverage, whether flashing is new or reused, ventilation, the per-sheet decking rate, permit, and cleanup. A one-line quote for "new roof, $14,500" is not an estimate.

3. 3

   Confirm a permit is being pulled

   Most municipalities in Midvale require a permit for a full replacement. Skipping it saves the contractor a few hundred dollars and can cost you at resale.

4. 4

   Ask who is physically doing the work

   Employed crew or subcontracted? Neither answer is disqualifying, but a company that will not answer plainly is telling you something.

5. 5

   Ask for the two warranties by name

   The manufacturer warranty covers the shingles. The workmanship warranty covers the installation, and it is only as good as the company behind it. Ask how long they have been operating locally.

6. 6

   Never pay in full up front

   A deposit is normal. Paying the full amount before materials are on site is not, and it removes every bit of leverage you have.

Some of the least expensive full replacements in the valley thanks to small footprints. Townhome and condo work runs through an HOA and is usually priced per building.

That range assumes a complete tear-off, synthetic underlayment, ice-and-water shield at the eaves and valleys, new flashing, and ridge ventilation. A quote materially below it is usually missing one of those, not finding a cheaper shingle.

Here is the full sequence for a typical Midvale project, so nothing on the day is a surprise.

1. 1

   Free inspection

   We get on the roof, photograph what we find, and check the attic where access allows. Ventilation and decking condition get looked at, not assumed.

2. 2

   Written estimate

   You get an itemized scope, a material selection, a price, and a plain-language explanation of anything we flagged. No same-day-signature discount, ever.

3. 3

   Scheduling and materials

   We book the date, order material, and pull the permit. Material is usually delivered the day before or the morning of.

4. 4

   Protection and tear-off

   Landscaping, AC units, and driveways get covered. The old roof comes off down to the deck. On most homes this is the loudest three hours of the project.

5. 5

   Deck inspection

   With the roof off, we walk every square foot of decking. Soft or rotted sheets are replaced and counted, and you see the count before we cover it up.

6. 6

   Dry-in

   Ice-and-water shield at eaves, valleys, and penetrations. Synthetic underlayment across the field. The house is weather-tight from this point forward.

7. 7

   Flashing and ventilation

   New flashing at walls, chimneys, and penetrations. Ridge vent cut and installed, intake ventilation verified.

8. 8

   Shingles, ridge, and cleanup

   Field shingles, then hip and ridge cap. Magnet sweep of the yard and driveway, debris hauled off the same day.

9. 9

   Final walkthrough

   We walk it with you, hand over the warranty paperwork, and the final payment is due after you have seen the finished job — not before.

• Attic ice dam mitigation on bench and canyon-mouth homes
• Low-slope and flat sections in TPO, EPDM, and modified bitumen
• Detached garage, shop, and outbuilding roofs
• Gutter and fascia repair as part of a roof project
• Roof certifications for real estate transactions
• Leak diagnosis and repair — including the leaks two other companies could not find
• Full tear-off and replacement in asphalt, metal, and tile
• Storm, wind, and hail damage assessment, with insurance claim documentation
• Flashing, valley, chimney, and skylight work
• Ridge and intake ventilation correction

Midvale has a lot of smaller-footprint homes, which is genuinely good news on price — a straightforward Midvale ranch is one of the least expensive full roof replacements in the valley. Townhome and condo work here usually runs through an HOA, and we are used to that paperwork.

Older Midvale homes frequently have undersized or original gutters that cannot keep up with a fast spring melt, and that backup is what pushes water behind the fascia.

Housing here is small older homes and bungalows near Main Street, 1960s–80s ranches through the middle, and newer townhome and condo development at Bingham Junction. We work throughout Historic Midvale, the Bingham Junction area, the Fort Union corridor, the State Street corridor, and the rest of Midvale — including everything near Bingham Junction.

ZIP codes we serve in Midvale: 84047.

We have been roofing the Salt Lake Valley since 2011. The thing customers mention most is not the roof — it is that we told them what we actually found, including the times that meant not selling them anything.

• Licensed and insured in the state of Utah
• Free, no-pressure roof inspections and written estimates
• Manufacturer-certified installers on every crew
• Workmanship warranty on every full replacement
• We handle the insurance paperwork on storm claims
• Financing available with approved credit

If your roof has years left, we will say so and put it in the report. That costs us a sale today and it is the reason we are still here.

We work throughout Midvale — Historic Midvale, the Bingham Junction area, the Fort Union corridor, the State Street corridor — and everything around Bingham Junction, Historic Main Street, the Jordan River Parkway. Midvale has roughly 36,000 residents and sits in Salt Lake County.

Older Midvale homes frequently have undersized or original gutters that cannot keep up with a fast spring melt, and that backup is what pushes water behind the fascia.