Roofers in Magna, UT

Roofing has a low barrier to entry and a long feedback loop — a bad install can look perfect for four years. These are the checks that actually separate companies, in rough order of how much they tell you.

1. 1

   Verify the Utah license, then verify the insurance separately

   Ask for the DOPL license number and look it up yourself. Then ask for a certificate of insurance sent directly from the insurance agent, not a PDF forwarded by the contractor. Both general liability and workers’ compensation. If a worker is hurt on an uninsured crew, the exposure can land on the homeowner.

2. 2

   Require the scope in writing, itemized

   Underlayment type, ice-and-water shield coverage, whether flashing is new or reused, ventilation, the per-sheet decking rate, permit, and cleanup. A one-line quote for "new roof, $14,500" is not an estimate.

3. 3

   Confirm a permit is being pulled

   Most municipalities in Magna require a permit for a full replacement. Skipping it saves the contractor a few hundred dollars and can cost you at resale.

4. 4

   Ask who is physically doing the work

   Employed crew or subcontracted? Neither answer is disqualifying, but a company that will not answer plainly is telling you something.

5. 5

   Ask for the two warranties by name

   The manufacturer warranty covers the shingles. The workmanship warranty covers the installation, and it is only as good as the company behind it. Ask how long they have been operating locally.

6. 6

   Never pay in full up front

   A deposit is normal. Paying the full amount before materials are on site is not, and it removes every bit of leverage you have.

Small, simple roofs near Main Street keep totals low. The offset is that lake-plain air is hard on metal, so flashing and fasteners should be upgraded rather than reused.

That range assumes a complete tear-off, synthetic underlayment, ice-and-water shield at the eaves and valleys, new flashing, and ridge ventilation. A quote materially below it is usually missing one of those, not finding a cheaper shingle.

Here is the full sequence for a typical Magna project, so nothing on the day is a surprise.

1. 1

   Free inspection

   We get on the roof, photograph what we find, and check the attic where access allows. Ventilation and decking condition get looked at, not assumed.

2. 2

   Written estimate

   You get an itemized scope, a material selection, a price, and a plain-language explanation of anything we flagged. No same-day-signature discount, ever.

3. 3

   Scheduling and materials

   We book the date, order material, and pull the permit. Material is usually delivered the day before or the morning of.

4. 4

   Protection and tear-off

   Landscaping, AC units, and driveways get covered. The old roof comes off down to the deck. On most homes this is the loudest three hours of the project.

5. 5

   Deck inspection

   With the roof off, we walk every square foot of decking. Soft or rotted sheets are replaced and counted, and you see the count before we cover it up.

6. 6

   Dry-in

   Ice-and-water shield at eaves, valleys, and penetrations. Synthetic underlayment across the field. The house is weather-tight from this point forward.

7. 7

   Flashing and ventilation

   New flashing at walls, chimneys, and penetrations. Ridge vent cut and installed, intake ventilation verified.

8. 8

   Shingles, ridge, and cleanup

   Field shingles, then hip and ridge cap. Magnet sweep of the yard and driveway, debris hauled off the same day.

9. 9

   Final walkthrough

   We walk it with you, hand over the warranty paperwork, and the final payment is due after you have seen the finished job — not before.

• Roof certifications for real estate transactions
• Leak diagnosis and repair — including the leaks two other companies could not find
• Full tear-off and replacement in asphalt, metal, and tile
• Storm, wind, and hail damage assessment, with insurance claim documentation
• Flashing, valley, chimney, and skylight work
• Ridge and intake ventilation correction
• Attic ice dam mitigation on bench and canyon-mouth homes
• Low-slope and flat sections in TPO, EPDM, and modified bitumen
• Detached garage, shop, and outbuilding roofs
• Gutter and fascia repair as part of a roof project

Magna sits right at the base of the Oquirrhs, and homes here take wind straight off the mountains and the lake plain. The older cottages near Main Street are small and simple to reroof, which keeps costs down, but many still have original plank decking under the shingles.

Wind exposure here is among the highest in the valley, and salt-laden air off the lake plain is hard on exposed metal — flashings, valleys, and fasteners age faster than they would elsewhere.

Housing here is older company-era cottages and small homes near Main Street, alongside newer subdivisions built out toward the lake side. We work throughout Historic Magna, the Main Street area, the 3500 South corridor, the Lake Park edge, and the rest of Magna — including everything near Historic Main Street.

ZIP codes we serve in Magna: 84044.

We have been roofing the Salt Lake Valley since 2011. The thing customers mention most is not the roof — it is that we told them what we actually found, including the times that meant not selling them anything.

• Licensed and insured in the state of Utah
• Free, no-pressure roof inspections and written estimates
• Manufacturer-certified installers on every crew
• Workmanship warranty on every full replacement
• We handle the insurance paperwork on storm claims
• Financing available with approved credit

If your roof has years left, we will say so and put it in the report. That costs us a sale today and it is the reason we are still here.

We work throughout Magna — Historic Magna, the Main Street area, the 3500 South corridor, the Lake Park edge — and everything around Historic Main Street, the Oquirrh Mountains, the Great Salt Lake shoreline. Magna has roughly 29,000 residents and sits in Salt Lake County.

Wind exposure here is among the highest in the valley, and salt-laden air off the lake plain is hard on exposed metal — flashings, valleys, and fasteners age faster than they would elsewhere.